Processing Power Connectors and Wiring Harnesses
The power connector developed by YAXUN can connect to power in various applications such as household appliances, satellites and even subsea equipment! So, whether you need to connect the battery in the handheld device or supply power to the control panel of the home appliance, YAXUN can provide a suitable solution to meet your power connection needs. Please contact YAXUN to take advantage of our wide range of power connectors. These connectors will allow you to find the most suitable solution to meet the unique requirements of your application.
A printed circuit board power contactor used to connect a sub-printed circuit board to an engaging contactor of another electrical component. The power contactor includes: A main section. At least one sub-board electrical contact section extending from the main section. And at least one engagement connector contact section extending from the main section. The engaging connector contact section includes at least three beams protruding forward. The first beam of the beams extends outward along a first direction in which the first beam extends forward from the main section and has a contact surface facing the first direction. Two second beams of the beams are located on two opposite sides of the first beam and extend outward in opposite second directions in which the second beams extend forward from the main section. The second beams have contact surfaces facing the second direction.
|
Precision screw machining Type II pin and socket terminals have high normal force and low resistance. The interface is closed to prevent damage due to misalignment. Power terminal type: terminal Terminal contact part plating material: gold Connector system: wire to wire |
|
The female end terminal triple lock power connector device is plugged into the corresponding male end terminal. Available in a variety of sizes and materials. Power terminal type: terminal Operating Voltage(VAC): 600 Operating Voltage(VDC): 600 Terminal contact part plating material: pre-tinned Connector system: wire to wire |
|
The pin and socket terminal size of the precision-formed type III reinforced scattered parts is 16. The terminal has the characteristics of high normal force and low resistance. The single contact current rating of the reinforced terminal is 24A (at 30°C T-Rise). Power terminal type: terminal Wire Size(AWG): 18 – 14 Wire Size(mm²): .8 – 2 Connectors and terminals are terminated to: wires and cables Cable termination method: crimp |
|
Triple lock power connector: glow wire cap The glow wire (GWT, V0, NF 750°C) triple lock power connector cap is inserted into the corresponding plug. They are equipped with male terminals and provide a variety of options. Rectangular power connector type: sheath Connector and housing type: female end, female end Connector system: wire to wire Center line (spacing) (mm): 6 Sealable: No |
| Circular power connector |
CMC Series 1 is a metal shell circular plastic connector (CPC) for added strength and protection. Shell sizes are 14-5, 14-7, 22-16, 28-24 and 28-37 The CPC Series 1 cable or panel mount connector accepts durable Multimate terminals, enabling the application of multiple combinations of signals and coaxial circuits in the same sheath. 4 to 37 digits. CPC Series 3 connector with power up to 47A. 3-7 positions, compatible with XII type "box" power terminals. The wiring range of the terminal is 16-10 AWG. The CPC Series 1 connector with cylindrical pin connector can be combined with durable Multimate terminals to realize the application of multiple signal and coaxial circuit combinations in the same sheath. 4 to 37 digits. The Mini CPC connector is compatible with the existing Mini-Universal MATE-N-LOK pin and socket contacts and complies with the 30-22 American Wire Gauge. Two housing sizes (8 or 11) are available, which can accommodate 1-4 and 5-9 positions. High contact density and IP67 sealing. CPC Series 2 connectors with cylindrical terminals accept No. 20 DF (precision formed) and No. 20 DM (automatic lathe processing) pins and an interface socket with a pin diameter of .040 [1.02]. 8 to 63 bits. |
| Battery connector and battery holder |
FBIS II Plug and Receptacle Assemblies PLUG ASSY, PB-FREE, 2.5MM PITCH BATTERY C 2.5 BATTERY CONN PLUG 10P STD .050CL, CHAMP, VERT PLUG, 100 POS MDI HEADER ASSEMBLY, 6P HDR ASY, VERT, RET TAIL, 10.8V .050CL, CHAMP, R/TANG RCPT, 60POS REC ASSY 0.6mm CHAMP DOCKING C |
| Power bus connector |
Detachable interface with forced lock, polarity positioning and terminal frame 2.54 [0.100] Right angle and vertical joints on the center can be adapted to the standard 1.02 [0.040] PCB hole diameter The four-cable self-calibrating connector corrects coaxial 2.03 [0.080] deviations, and each cable is measured at 80 amps (30ºC temperature rise), depending on the application The unique tap allows the trunk line to branch to serve multiple distribution points Accessories are measured at 70-110 amperes (30ºC temperature rise), depending on the installation interface Approved by the American Safety Testing Laboratory Corporation's Component Program, document numbers E28476, E13288 and E53799 Obtained Canadian Standards Association certification, file number LR7189A-149 The first flat cable tap that allows trunk branching, side tapping, and discrete wire tapping Blind mating drawer connector adopts serial plug and single contact |
| Power terminal |
 POWERBAND terminal The precision-formed .125 AMP POWERBAND pin and socket power terminals are high-current terminals that provide electrical performance and the economy and productivity of strip-feeding, precision-molded terminals. Precision screw machining Type II pin and socket terminals have high normal force and low resistance. The interface is closed to prevent damage due to misalignment. The pin and socket terminal size of the precision-formed Type III scattered parts is 16. The terminal has the characteristics of high normal force and low resistance. The interface is closed to prevent damage due to misalignment. The pin and socket terminal size of the precision-formed Type III scattered parts is 16. The terminal has the characteristics of high normal force and low resistance. The interface is closed to prevent damage due to misalignment. The terminal triple lock power connector device of the female end is plugged into the corresponding male end terminal. Available in a variety of sizes and materials. |
| Rectangular power connector |
 The connector of the high temperature resistant triple lock power connector is plugged into the corresponding plug. Provide a variety of options. The glow wire (GWT, V0, NF 750°C) triple lock power connector cap is inserted into the corresponding plug. They are equipped with male terminals and provide a variety of options. The standard temperature double lock power connector is plugged into the corresponding plug. The locking piece is suitable for male and female ends to ensure that the terminal is installed in place and prevent the terminal from falling off. The standard temperature triple lock power connector plug is plugged into the corresponding cap or head. They are equipped with female terminals and provide a variety of options. |
| Backplane power connector |
COAXIAL RF SOCKET, SZ 5 RA Keyed Guide Mod. Vita 46, Machined Keyed Guide Pin, Machined, Vita 46 SOCKET CONTACT, QUADRAX, SZ8, RR MULTIGIG RT PWR .8" R/A HDR 4P PBFR |
| Panel and PCB socket |
CNV OUTLET PCBOARD MNT, BLK LF CONV OUTLET ASSEMBLY (BLACK) CONV OUTLET ASSY (PUTTY WHITE) CNV OUTLET PCBOARD MNT, WHT LF HOUSING, CONV OUTLET, DUMMY |
